LFD Chisel....

[bigdix]

So I smoked my first one of these tonight after dinner.....delicious. Glad I ate and had a drink on hand (thanks for the tip kelmac & Ogre!), I may have to review this one quite soon, unfortunately I don't think I'll need a cigar for a few days, friggin' nicotine sammich!! :dr

[Chingas]

Smoke a few more and do a review if you would. That would be great!

[bigdix]

Smoke a few more and do a review if you would. That would be great!

No problem, brother...plan on it!! :tu

[Chingas]

No problem, brother...plan on it!! :tu

That's kind of what I was thinking...

[longknocker]

Is This The Highest Nicotine Content Stick Out There? Just Curious.:)

[bigdix]

Is This The Highest Nicotine Content Stick Out There? Just Curious.:)

Perhaps some others can chime in on this one...not sure. :confused:

[Ogre]

Glad you liked it, it is one of my regulars.

[RHNewfie]

I really like these, gonna have to grab some when I am states-side!

[jonumberone]

So I smoked my first one of these tonight after dinner

How did you cut it?

I usually cut on an angle.

[Patrick B]

Great cigar. I should smoke it more often...

[bigdix]

How did you cut it?

I usually cut on an angle.

Just took the Palio to it...I took off about a quarter inch. Not sure if I'm doing it right, I actually thought while I was cutting it, "Wonder if I should put up a thread asking how folks cut these?".

[KenyanSandBoa]

Great smoke...one of my favorite LFDs.

How did you cut it?

I usually cut on an angle.

:tpd:...for the chisel and any torp. :tu

[bigdix]

Great smoke...one of my favorite LFDs.



:tpd:...for the chisel and any torp. :tu

for the torp (since they are round at the head) the angle makes sense...what about the "flat" head on the chisel..how do you angle the cut?

[kelmac07]

These in a maduro are YUMMY!! :dr :dr

[bigdix]

These in a maduro are YUMMY!! :dr :dr

That's what I had brother...kinda chocolatey and oily lookin'?? :dr

[kelmac07]

That's what I had brother...kinda chocolatey and oily lookin'?? :dr

That's the one!! :tu :tu

[bobarian]

Is This The Highest Nicotine Content Stick Out There? Just Curious.:)

The LFD Chisel is light compared to the higher end Litto Gomez Diez Chisel. :tu

[jonumberone]

for the torp (since they are round at the head) the angle makes sense...what about the "flat" head on the chisel..how do you angle the cut?

Just tilt the cutter. Just imagine cutting it with a knife. try and keep the angle of the tip, your just removing the cap to get the smoky goodness out.
I try to make a consious effort to have the cut end down in my mouth so the smoke hits my tongue VS the roof of my mouth.

[bigdix]

The LFD Chisel is light compared to the higher end Litto Gomez Diez Chisel. :tu

Can't find the damn things Bob!! Been lookin' too, you find any let me know!!

Just tilt the cutter. Just imagine cutting it with a knife. try and keep the angle of the tip, your just removing the cap to get the smoky goodness out.
I try to make a consious effort to have the cut end down in my mouth so the smoke hits my tongue VS the roof of my mouth.

Thanks for the tip, brother (no pun intended). I'll try it with the next one!! :ss

[NCRadioMan]

The LFD Chisel is light compared to the higher end Litto Gomez Diez Chisel. :tu

I don't have that experience, Bob. To me, the regular line is stronger than the Litto's. Then again, I am strange.

The AirBender Chisel is coming. Also a great 5 pack Chisel sampler with a Chisel, Chisel Maduro, AirBender Chisel, Coronado Chisel and Cameroon Chisel.

[bigdix]

That might be a sampler I have to have, NC!! :ss

[BigAsh]

How did you cut it?

I usually cut on an angle.

Love these...and the smaller "Chiselito"...I usually just "pinch" the chisel tip and it pops open so no need to cut...

[KenyanSandBoa]

Just tilt the cutter. Just imagine cutting it with a knife. try and keep the angle of the tip, your just removing the cap to get the smoky goodness out.
I try to make a consious effort to have the cut end down in my mouth so the smoke hits my tongue VS the roof of my mouth.

:tpd:...same here. Maybe it's just me, but I usually cut my torps with my cutter lined up left to right, but I have to cut the chisels with the cutter lined up up and down because of the bill on it.

[Mr B]

Very tasty stick. I am a fan of the Chiselito.